Breaking News

RedLake Motion Meter






Kamera High Speed Video merek Redlake MotionMeter ini merupakan cikal bakal dari kamera Fastec. Kamera ini mempunyai sensor CCD dengan maksimum resolusi sebesar 292 x 220 pixels yang mampu merekam 500 fps pada resolusi tersebut. Frame rate maksimumnya adalah 1.000 fps dengan resolusi 292 x 110 pixels.


Spesifikasi Teknis


Image Resolution: 
292 x 220 pixels per frame. 60 thru 500 fps. 292 x 110 pixels on a half-height frame at 1000 fps.

Lens Mount: 
Standard C-Mount lens.

Record Rates:
(50 PAL, 60 NTSC), 125, 250, 500 and 1000 fps.

Shutter Speed:
Electronic shutter operates at rates of 1X to 20X of record rates.
Exposure time ranges from 1/60th sec. to 1/20,000th sec.

Live/Setup Mode: 
The camera comes up in Live mode at power on. The camera returns to Live mode when record or playback is terminated.

Record Mode:
Records when you press red button:
Continues to store images in the memory until you press:
Stops recording so that all frames precede the frame active when the button was pressed.

Trigger:
When the Trigger signal stops recording, the camera may continue to store images to the end of the buffer, depending on the Trigger Point setting.

Frame Storage:
Standard Capacity: 1,024 frames (2,048 at 1000fps).
Enhanced Capacity: 2,048 frames (4,096 at 1000pfs).

Playback Mode:
Plays back in either direction at the selected rate when you press the Play buttons.

Playback Rates:
Single Step, 1, 2, 3, 4, 5, 10, (25 PAL, 30 NTSC), (50 PAL, 60 NTSC), 125, 250, 500, and 1000 frames per second, forward or reverse.

Status Display:
Record Rate, Shutter, Trigger Point, Trig (trigger actuated), Event #, Frame #, Time of Frame (ms).

External Connections Digital In:
BNC connector PCB mount, software selectable for Phase Lock In or Event Marker Input. Normally set to OFF.

Phase Lock In:
TTL rising edge from 0 to 3.3 volts. PHASE LOCK IN is pulled to +3.3 volts with an internal 10K ohm resistor. Designate each unit as a master or slave.

Event Marker Input:
One TTL input through a BNC connector on the Camera cable. Input normally at +3.3 volts (white marker) falling to 0 volts by a contact closure (black marker).

Digital Out:
BNC connector PCB mount, software selectable for Phase Lock Out or Strobe Out.

Phase Lock Out:
TTL rising edge from 0 to 3.3 volts.

Strobe Output:
TTL pulse normally low, goes high during exposure.

Video Output: 
BNC connector to VCR's and external monitors. RS-170 NTSC or PAL, software selectable.

Trigger Input: 
BNC connector (PCB mount).  Accepts three signal formats:
(1) 0-volt input (held to ground by a 2K resistor at the source), rising to +3.3 volts (up to +30 volts permitted).
(2) Contact closure, rising to +3.3 volts when contact opens.
(3) Contact closure at +3.3 volts, falling to 0 volts when the contact opens.

Size, Power and Operating Environment
Camera Dimensions:
8. 3” (211mm) wide x 5.5” (140mm) high x 2.5 (64mm) deep.

Weight: 
1.5 lb. (0.7 kg) without lens.

Power: 
12 volts DC 2 Amps.
 Redlake supplies a Panasonic EB-P0783B universal input voltage AC-DC power converter that includes a power switch, or equivalent.

Operating Environment: 
0°F to 115° F (-18°C to 40°C).

No comments